ADM223 View Datasheet(PDF) - Analog Devices
Part Name
Description
Manufacturer
ADM223 Datasheet PDF : 16 Pages
| |||
ADM223/ADM230L–ADM241L
Mnemonic
VCC
V+
V–
GND
C+
C–
C1+
C1–
C2+
C2–
TIN
TOUT
RIN
ROUT
EN/EN
SD/SD
NC
PIN FUNCTION DESCRIPTION
Function
Power Supply Input 5 V ± 10% (5 V ± 5% ADM233L, ADM235L).
Internally generated positive supply (+10 V nominal) on all parts except ADM231L and ADM239L.
ADM231L, ADM239L requires external 7.5 V to 13.2 V supply.
Internally generated negative supply (–10 V nominal).
Ground pin. Must be connected to 0 V.
(ADM231L and ADM239L only). External capacitor (+ terminal) is connected to this pin.
(ADM231L and ADM239L only). External capacitor (– terminal) is connected to this pin.
(ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor (+ terminal)
is connected to this pin.
(ADM233L) The capacitor is connected internally and no external connection to this pin is required.
(ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor (– terminal)
is connected to this pin.
(ADM233L) The capacitor is connected internally and no external connection to this pin is required.
(ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor (+ terminal)
is connected to this pin.
(ADM233L) Internal capacitor connections, Pins 11 and 15 must be connected together.
(ADM230L, ADM232L, ADM234L, ADM236L, ADM237L, ADM238L, ADM241L) External capacitor (– terminal)
is connected to this pin.
(ADM233L) Internal capacitor connections, Pins 10 and 16 must be connected together.
Transmitter (Driver) Inputs. These inputs accept TTL/CMOS levels. An internal 400 kΩ pull-up resistor to VCC is
connected on each input.
Transmitter (Driver) Outputs. These are RS-232 levels (typically ± 10 V).
Receiver Inputs. These inputs accept RS-232 signal levels. An internal 5 kΩ pull-down resistor to GND is connected on
each input.
Receiver Outputs. These are TTL/CMOS levels.
Enable Input. Active low on ADM235L, ADM236L, ADM239L, ADM241L. Active high ADM223. This input is used
to enable/disable the receiver outputs. With EN = low (EN = high ADM223), the receiver outputs are enabled. With
EN = high (EN = low ADM223), the outputs are placed in a high impedance state. This facility is useful for
connecting to microprocessor systems.
Shutdown Input. Active high on ADM235L, ADM236L, ADM241L. Active low on ADM223. With SD = high on the
ADM235L, ADM236L, ADM241L, the charge pump is disabled, the receiver outputs are placed in a high impedance
state and the driver outputs are turned off. With SD low on the ADM223, the charge pump is disabled, the driver
outputs are turned off and all receivers except R4 and R5 are placed in a high impedance state. In shutdown, the power
consumption reduces to 5 µW.
No Connect. No connections are required to this pin.
Table I. ADM235L, ADM236L, ADM241L Truth Table
SD EN
00
01
10
Status
Normal Operation
Normal Operation
Shutdown
Transmitters
T1–T5
Enabled
Enabled
Disabled
Receivers
R1–R5
Enabled
Disabled
Disabled
Table II. ADM223 Truth Table
SD EN Status
Transmitters Receivers
T1–T4
R1–R3 R4, R5
0 0 Shutdown
Disabled
0 1 Shutdown
Disabled
1 0 Normal Operation Enabled
1 1 Normal Operation Enabled
Disabled Disabled
Disabled Enabled
Disabled Disabled
Enabled Enabled
–10–
REV. B
Share Link: 