LC72711LW View Datasheet(PDF) - SANYO -> Panasonic

Part Name

Description

Manufacturer

LC72711LW

Mobile FM Multiplex Broadcast (DARC) Receiver IC

SANYO -> Panasonic 

LC72711W, 72711LW

Continued from preceding page.

Address Register

Function

R/W Address Register

Function

1

BIC

Number of allowable BIC errors

W

1

STAT

Status register

2

SYNCB Block synchronization: error protection count

W

2

BLNO Block number register

3

SYNCF Frame synchronization: error protection count

W

4

CTL1

Control register 1

W

5

CTL2

Control register 2

W

6

CRC4 Layer 4 CRC register

W

Number of Allowable BIC Errors

Address Register R/W Initial value

BIT7

BIT6

BIT5

BIT4

BIT3

BIT2

BIT1

01H

BIC

W

22H

Back protection

(LSB)

Forward protection

R/W

R

R

BIT0

(LSB)

The synchronization circuit in this IC operates by recognizing a 16-bit BIC code. The number of allowable errors is the

number of incorrect bits allowed in those 16 bits. This data sets up separate values for forward protection mode (when

synchronized) and for back protection mode (when not synchronized).

The default value is to allow 2 incorrect bits in both forward and back modes. If the block synchronization

discrimination output (BLOCK) is used for discriminating whether or not FM multiplex data is present, we recommend

setting the back protection mode BIC allowable error count to 1 or 0.

Block Synchronization: Error Protection Count

Address Register R/W Initial value

BIT7

BIT6

BIT5

BIT4

BIT3

BIT2

BIT1

BIT0

02H SYNCB W

17H

Back protection

(LSB)

Forward protection

(LSB)

The synchronization protection count can be set separately for both forward and back protection. The count conditions

for the protection counts are as follows.

• Back protection mode (not synchronized: BLOCK=low)

If the timing of the IC internal synchronization free-running counter matches the timing of the received BIC, the

protection count is incremented by 1. Contrarily, if the timings of the IC internal counter and the received BIC do not

match, the protection counter is cleared to 0. The timing of the count is the timing of the IC internal counter.

• Forward protection mode (synchronized: BLOCK=high)

In reverse to the back protection mode, if the timing of the IC internal free-running counter does not match the

detection timing of the received BIC, the protection counter is incremented, and if the timings match, the protection

counter is cleared to 0.

Figure 1 shows the states of the protection counter for the cases where the forward and back protection counts are both

3. This IC defines the value of the protection counter to be 1 at the point that a match or a discrepancy occures between

the IC internal timing and the timing of the received BIC occurs. For example, when the value of the back protection

count is 2, the IC internal timing and the timing of the received BIC will have matched two times consecutively.

If the protection data is set to new values, for example if the protection counts are set to 3 as assumed in figure 1,

applications must send values which are 1 less than the intended value; in this case 22H. Similarly, if the value is set to

00H, the protection counts will, by definition, be set to 1 for both the forward and back directions. However, note that

the resulting operation will be equivalent to there being no protection circuit. The default values are 8 for the forward

protection count and 2 for the back protection count.

If the block synchronization output (BLOCK) is used for discriminating whether or not FM multiplex data is present,

we recommend setting the block synchronization back protection count to a value that is more strict than the default

value. (That is, we recommend replacing the default value of 2 with a value of 3 or higher.)

Received data

BIC

123

010

Synchronization

counter BIC position

Reset

123

Block

* Assumes that the forward and

back protection counts are 3.

Figure 1 Block Synchronization Protection Operation (Forward → Back → Forward)

No.6167-8/26

Share Link: