TSOP38156(2018) View Datasheet(PDF) - Vishay Semiconductors
Part Name
Description
Manufacturer
TSOP38156 Datasheet PDF : 7 Pages
| |||
www.vishay.com
TSOP381.., TSOP383.., TSOP385..
Vishay Semiconductors
BLOCK DIAGRAM
16833-13
3
30 kΩ
1
Input
AGC
Band
pass
Demo-
dulator
2
PIN
Control circuit
APPLICATION CIRCUIT
17170-11
Transmitter IR receiver
with
TSALxxxx
VS
OUT
GND
R1
C1
VO
+ VS
μC
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Supply current
Output voltage
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tamb ≤ 85 °C
t ≤ 10 s, 1 mm from case
VS
-0.3 to +6
V
IS
3
mA
VO
-0.3 to (VS + 0.3)
V
IO
5
mA
Tj
100
°C
Tstg
-25 to +85
°C
Tamb
-25 to +85
°C
Ptot
10
mW
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
Supply current
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
ISD
0.27
0.35
0.45
ISH
-
0.45
-
Supply voltage
VS
2.5
-
5.5
Transmission distance
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
d
-
Output voltage low
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL
-
24
-
-
100
Minimum irradiance
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
Ee min.
-
0.12
0.25
Maximum irradiance
Directivity
tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
Ee max.
30
-
-
Angle of half transmission distance
ϕ1/2
-
± 45
-
UNIT
mA
mA
V
m
mV
mW/m2
W/m2
°
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.40
Ee
Optical Test Signal
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
0.35
t
tpi *)
T
*) tpi ≥ 6/f0 is recommended for optimal function
VO
VOH
Output Signal
1) 3/f0 < td < 9/f0
2) tpi - 4/f0 < tpo < tpi + 6/f0
14337
VOL
td 1)
tpo 2)
t
0.30
0.25
Output pulse width
0.20
0.15
Input burst length
0.10
0.05
λ = 950 nm,
optical test signal, Fig. 1
0
0.1
1
10 100
1000 10 000 100 000
20771
Ee - Irradiance (mW/m²)
Fig. 1 - Output Active Low
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Rev. 1.6, 12-Apr-18
2
Document Number: 81743
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Share Link: 