HMU17/883 View Datasheet(PDF) - Intersil
Part Name
Description
Manufacturer
HMU17/883 Datasheet PDF : 6 Pages
| |||
HMU17/883
TABLE 2. AC ELECTRICAL PERFORMANCE SPECIFICATIONS
Device Guaranteed and 100% Tested
PARAMETER
SYMBOL
(NOTE 1)
CONDI-
TIONS
GROUP
A
SUB-
GROUP
S
TEMPERATURE
(oC)
-45
-60
MIN MAX MIN MAX
UNITS
Unclocked Multiply Time
t MUC
9, 10, 11
-55 ≤ TA ≤ 125
-
70
-
90
ns
Clocked Multiply Time
tMC
9, 10, 11
-55 ≤ TA ≤ 125
-
45
-
60
ns
X, Y, RND Setup Time
tS
9, 10, 11
-55 ≤ TA ≤ 125
18
-
20
-
ns
Clock HIGH Pulse Width
tPWH
9, 10, 11
-55 ≤ TA ≤ 125
15
-
20
-
ns
Clock LOW Pulse Width
tPWL
9, 10, 11
-55 ≤ TA ≤ 125
15
-
20
-
ns
MSPSEL to Product Out tPDSEL
9, 10, 11
-55 ≤ TA ≤ 125
-
25
-
30
ns
Output Clock to P
tPDP
9, 10, 11
-55 ≤ TA ≤ 125
-
25
-
30
ns
Output Clock to Y
tPDY
9, 10, 11
-55 ≤ TA ≤ 125
-
25
-
30
ns
Three-State Enable
Time
tENA
(Note 6)
9, 10, 11
-55 ≤ TA ≤ 125
-
25
-
30
ns
Clock Enable Setup
tSE
9, 10, 11
-55 ≤ TA ≤ 125
15
-
15
-
ns
NOTES:
5. AC Testing as follows: VCC = 4.5V and 5.5V. Input levels 0V and 3.0V; Timing reference levels = 1.5V; output load per test load
circuit, with V1 = 2.4V, R1 = 500Ω and CL = 40pF.
6. Transition is measured at ±200mV from steady state voltage, output loading per test load circuit, with V1 = 1.5V, R1 = 500Ω and
CL = 40pF.
TABLE 3. ELECTRICAL PERFORMANCE SPECIFICATIONS
PARAMETER
SYMBOL
CONDITIONS
NOTES
TEMPERATURE (oC)
-45
MIN MAX
-60
MIN MAX UNITS
Input Capacitance
CIN VCC = Open,
7
f = 1MHz
Output Capacitance
COUT All Measurements
7
I/O Capacitance
CI/O are referenced to
7
device GND.
TA = 25
TA = 25
TA = 25
-
15
-
15
pF
-
10
-
10
pF
-
10
-
10
pF
X, Y, RND Hold Time
tH
Three-State Disable
tDIS
Time
7, 8
7, 8, 9
-55 ≤ TA ≤ 125
-55 ≤ TA ≤ 125
3
-
3
-
ns
-
25
-
30
ns
Clock Enable Hold
tHE
Time
7, 8, 9
-55 ≤ TA ≤ 125
3
-
3
-
ns
Output Rise Time
tR
From 0.8V to 2.0V
7, 8, 10
-55 ≤ TA ≤ 125
-
10
-
10
ns
Output Fall Time
tF
From 2.0V to 0.8V
7, 8, 10
-55 ≤ TA ≤ 125
-
10
-
10
ns
NOTES:
7. The parameters listed in Table 3 are controlled via design or process parameters and are not directly tested. These parameters are char-
acterized upon initial design and after major process and/or design changes.
8. Guaranteed, but not 100% tested.
9. Transition is measured at ±200mV from steady state voltage; output loading per test load circuit; with V1 = 1.5V, R1 = 500Ω and CL = 40pF.
10. Loading is as specified in the test load circuit, with V1 = 2.4V, R1 = 500Ω and CL = 40pF.
3-38
Share Link: 