MC10192FNR2 Просмотр технического описания (PDF) - ON Semiconductor

Номер в каталоге

Компоненты Описание

производитель

MC10192FNR2

Quad Bus Driver

ON Semiconductor 

MC10192

ELECTRICAL CHARACTERISTICS

Characteristic

Symbol

Pin

Under

Test

–30°C

Min

Max

Test Limits

+25°C

Min

Max

+85°C

Min

Max

Power Supply Drain Current

IE

8

154

140

154

Input Current

IinH

5

350

220

220

IinL

5

0.5

0.5

0.3

Output Current High

Logic 1

IOH

2

2.0

Output Current Low

Logic 0

IOL

2

13.5

18.0

14.0

18.0

14.0

19.0

Threshold Current High

Logic 1 IOHC

2

2.0

2.0

2.0

Threshold Current Low

Logic 0 IOLC

2

13.5

14.0

14.0

Output Sink Current Low

Logic 0

IOS

2

13.3

13.9

13.3

Load Return Voltage Absolute Max

Rating (Note 1.)

VLR

5.5

5.5

5.5

Output Voltage Low (Note 2.)

VOLS

–2.4

Switching Times

(50Ω Load)

Propagation Delay

E to Output tPHL

D to Output tPLH

2.0

6.0

1.5

4.5

Rise/Fall Time

(20 to 80%) tTLH

tTHL

3.3

1. The 5.5V value is a maximum rating, do not exceed. A 270Ω resistor will prevent output transistor breakdown.

2. Limitations of load resistor and load return voltage combinations. Refer to page 1 description.

Unit

mAdc

µAdc

µAdc

mAdc

mAdc

mAdc

mAdc

mAdc

V

V

ns

ELECTRICAL CHARACTERISTICS (continued)

TEST VOLTAGE VALUES (Volts)

@ Test Temperature

–30°C

VIHmax

–0.890

VILmin

–1.890

VIHAmin

–1.205

VILAmax

–1.500

VEE

–5.2

+25°C –0.810

–1.850

–1.105

–1.475

–5.2

+85°C –0.700

–1.825

–1.035

–1.440

–5.2

Characteristic

Power Supply Drain Current

Input Current

Output Current High

Logic 1

Output Current Low

Logic 0

Threshold Current High Logic 1

Threshold Current Low Logic 0

Output Sink Current Low Logic 0

Load Return Voltage Absolute Max

Rating (Note 1.)

Symbol

IE

IinH

IinL

IOH

IOL

IOHC

IOLC

IOS

VLR

Pin

Under

Test

8

5

5

2

2

2

2

TEST VOLTAGE APPLIED TO PINS LISTED BELOW

VIHmax

VILmin

VIHAmin

VILAmax

VEE

8

5

8

5

8

5,6,10,11

8

5,6,10,11

8

5,7,9,10,11

6

8

5,10,11

7,9

6

8

5,6,10,11

8

8

(VCC)

Gnd

16

16

16

16

16

16

16

16

16

Output Voltage Low (Note 2.)

VOLS

8

16

Each MECL 10,000 series circuit has been designed to meet the dc specifications shown in the test table, after thermal equilibrium has been

established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 linear fpm is maintained.

Outputs are terminated through a 50–ohm resistor to –2.0 volts. Test procedures are shown for only one gate. The other gates are tested in the

same manner.

http://onsemi.com

2

Share Link: