HA4404B Просмотр технического описания (PDF) - Intersil
Номер в каталоге
Компоненты Описание
производитель
HA4404B Datasheet PDF : 9 Pages
| |||
HA4404B
Electrical Specifications VSUPPLY = ±5V, RL = 10kΩ, VCS = 0.8V, Unless Otherwise Specified (Continued)
PARAMETER
(NOTE 4)
TEST CONDITIONS
TEMP. (oC) MIN
TYP
MAX
-3dB Bandwidth
±0.1dB Flat Bandwidth
Input Resistance
RS = 50Ω, CL = 11pF
RS = 24Ω, CL = 19pF
RS = 15Ω, CL = 34pF
RS = 11Ω, CL = 49pF
RS = 50Ω, CL = 11pF
RS = 24Ω, CL = 19pF
RS = 15Ω, CL = 34pF
RS = 11Ω, CL = 49pF
25
-
330
-
25
-
290
-
25
-
210
-
25
-
170
-
25
-
165
-
25
-
130
-
25
-
137
-
25
-
100
-
Full
200
400
-
Input Capacitance
Full
-
1.5
-
Enabled Output Resistance
Full
-
15
-
Disabled Output Capacitance
Differential Gain
VCS = 2.0V
4.43MHz, Note 3
Full
-
2.5
-
25
-
0.01
0.02
Differential Phase
4.43MHz, Note 3
25
-
0.01
0.02
Off Isolation
1VP-P, 100MHz, VCS = 2.0V,
Full
-
70
-
RL = 10Ω
Crosstalk Rejection
1VP-P, 30MHz
Full
-
80
-
Slew Rate (1.5VP-P, +SR/-SR)
RS = 50Ω, CL = 11pF
25
-
1280/1260
-
RS = 24Ω, CL = 19pF
25
-
1190/1170
-
RS = 15Ω, CL = 34pF
25
-
960/930
-
RS = 11Ω, CL = 49pF
25
-
810/790
-
Total Harmonic Distortion
10MHz, RL = 1kΩ, Note 3
Full
-
0.01
0.1
Disabled Output Resistance
VCS = 2.0V
Full
-
12
-
NOTES:
7. This parameter is not tested. The limits are guaranteed based on lab characterization, and reflect lot-to-lot variation.
8. Units are 100% tested at 25oC; guaranteed, but not tested at 0oC and 70oC.
UNITS
MHz
MHz
MHz
MHz
MHz
MHz
MHz
MHz
kΩ
pF
Ω
pF
%
Degrees
dB
dB
V/µs
V/µs
V/µs
V/µs
%
MΩ
AC Test Circuit
500Ω
400Ω 510Ω
VIN
75Ω
HA4404B
RS
-
+
10kΩ
75Ω
HFA1100
CX
VOUT
NOTE: CL = CX + Test Fixture Capacitance.
PC Board Layout
The frequency response of this circuit depends greatly on
the care taken in designing the PC board. The use of low
inductance components such as chip resistors and chip
capacitors is strongly recommended, while a solid
ground plane is a must!
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
(0.1µF) chip capacitor works well in most cases.
Keep input and output traces as short as possible, because
trace inductance and capacitance can easily become the
performance limiting items.
7
Share Link: 