MAX396C Просмотр технического описания (PDF) - Maxim Integrated
Номер в каталоге
Компоненты Описание
производитель
MAX396C Datasheet PDF : 12 Pages
| |||
Precision, 16-Channel/Dual 8-Channel,
Low-Voltage, CMOS Analog Multiplexers
ELECTRICAL CHARACTERISTICS—Single +5V Supply (continued)
(V+ = +5V ±10%, V- = 0V, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX
(Note 2)
UNITS
DYNAMIC
Transition Time (Note 3)
tTRANS VNO = 3V, Figure 2
Break-Before-Make Interval
Enable Turn-On Time
(Note 3)
Enable Turn-Off Time
(Note 3)
Charge Injection (Note 3)
tOPEN
tON(EN)
(Note 3)
tOFF(EN)
VCTE
CL = 100pF, VNO = 0V,
Figure 5
TA = +25°C
TA = TMIN to TMAX
105 245
ns
350
TA = +25°C
10
65
ns
TA = +25°C
TA = TMIN to TMAX
125 200
ns
275
TA = +25°C
TA = TMIN to TMAX
100 125
ns
200
TA = +25°C
1.5
5
pC
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = +3V ±10%, V- = 0V, GND = 0V, VAH = VENH = 2.4V, VAL = VENL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN TYP MAX
(Note 2)
UNITS
SWITCH
Analog Signal Range
VANALOG (Note 3)
V-
V+
V
On-Resistance
RON
INO = 1mA, VCOM = 1.5V,
V+ = 3V
TA = +25°C
TA = TMIN to TMAX
315 550
Ω
650
DYNAMIC
Transition Time (Note 3)
tTRANS
Figure 2, VIN = 2.4V,
VN01 = 1.5V, VN08 = 0V
TA = +25°C
TA = TMIN to TMAX
230 575
ns
750
Enable Turn-On Time (Note 3) tON(EN)
Figure 3, VINH = 2.4V,
VINL = 0V, VN01 = 1.5V
TA = +25°C
260 500
ns
Enable Turn-Off Time (Note 3) tOFF(EN)
Figure 3, VINH = 2.4V,
VINL = 0V, VN01 = 1.5V
TA = +25°C
135 400
ns
Charge Injection (Note 3)
VCTE
CL = 100pF, VNO = 0V,
Figure 5
TA = +25°C
1
5
pC
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = RON(MAX) - RON(MIN).
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal ranges, i.e., VNO = 3V to 0V and 0V to -3V.
Note 6: Leakage parameters are 100% tested at maximum rated hot operating temperature, and guaranteed by correlation at +25°C.
Note 7: Worst-case isolation is on channel 4 because of its proximity to the COM pin. Off-isolation = 20log VCOM/VNO, VCOM = output,
VNO = input to off switch.
Note 8: Leakage testing at single supply is guaranteed by correlation testing with dual supplies.
_______________________________________________________________________________________ 5
Share Link: 