MT88L85 Просмотр технического описания (PDF) - Mitel Networks

Номер в каталоге

Компоненты Описание

производитель

MT88L85

3V Integrated DTMF Transceiver with Power Down & Adaptive Micro Interface

Mitel Networks 

Advance Information

MT88L85

(DS). When DS is low, Motorola processor operation

is selected.

Figure 17 shows the timing diagram for the Motorola

MC68HC11 (1 MHz) microcontroller. The chip select

(CS) input is formed by NANDing address strobe

(AS) and address decode output. Again, the

MT88L85 examines the state of DS on the falling

edge of CS to determine if the micro has a Motorola

bus (when DS is low). Additionally, the Texas

Instruments TMS370CX5X is qualified to have a

Motorola interface. Figure 12(a) summarizes

connection of these Motorola processors to the

MT88L85 DTMF transceiver.

Figures 18 and 19 are the timing diagrams for the

Intel 8031/8051 (12 MHz) and 8085 (5 MHz) micro-

controllers with multiplexed address and data buses.

The MT88L85 latches in the state of RD on the

falling edge of CS. When RD is high, Intel processor

operation is selected. By NANDing the address

latch enable (ALE) output with the high-byte address

(P2) decode output, CS can be generated. Figure

12(b) summarizes the connection of these Intel

processors to the MT88L85 transceiver.

NOTE: The adaptive micro interface relies on high-

to-low transition on CS to recognize the

microcontroller interface and this pin must not be tied

permanently low.

The adaptive micro interface provides access to five

internal registers. The read-only Receive Data

Register contains the decoded output of the last

valid DTMF digit received. Data entered into the

write-only Transmit Data Register will determine

which tone pair is to be generated (see Table 1 for

coding details). Transceiver control is accomplished

with two control registers (see Tables 6 and 7), CRA

and CRB, which have the same address. A write

operation to CRB is executed by first setting the

most significant bit (b3) in CRA. The following write

operation to the same address will then be directed

to CRB, and subsequent write cycles will be directed

back to CRA. The read-only status register indicates

the current transceiver state (see Table 8).

A software reset must be included at the beginning

of all programs to initialize the control registers upon

power-up or power reset (see Figure 14). Refer to

Tables 4-7 for bit descriptions of the two control

registers.

The multiplexed IRQ/CP pin can be programmed to

generate an interrupt upon validation of DTMF

signals or when the transmitter is ready for more

data (burst mode only). Alternatively, this pin can be

configured to provide a square-wave output of the

call progress signal. The IRQ/CP pin is an open drain

output and requires an external pull-up resistor (see

Figure 13).

MC6800/6802

A0-A15

VMA

D0-D3

RW

Φ2

(a)

MT88L85

CS

RS0

D0-D3

R/W/WR

DS/RD

MC68HC11

A8-A15

AS

AD0-AD3

DS

RW

MT88L85

CS

D0-D3

RS0

DS/RD

R/W/WR

MC6809

MT88L85

8031/8051

8080/8085

MT88L85

A0-A15

Q

E

D0-D3

R/W

CS

RS0

D0-D3

R/W/WR

DS/RD

A8-A15

ALE

P0

RD

WR

CS

D0-D3

RS0

DS/RD

R/W/WR

(b)

Figure 12 a) & b) - MT88L85 Interface Connections for Various Intel and Motorola Micros

4-79

Share Link: