OPB828D Просмотр технического описания (PDF) - TT Electronics.
Номер в каталоге
Компоненты Описание
производитель
OPB828D Datasheet PDF : 6 Pages
| |||
Slotted Optical Switch
OPB827, OPB828, OPB829Z Series
Features:
0.125” (3.18 mm) wide, 0.315” (8.00 mm) deep slot
0.305” (7.75 mm) lead spacing (OPB827)
0.220” (5.59 mm) lead spacing (OPB828)
24-inch 26 AWG wire leads (OPB829)
Inexpensive plastic housing
OPB827
OPB828
OPB829Z
Description:
Each OPB827, OPB828 and OPB829 device consists of an infrared emitting diode (LED, 890 nm center wavelength) and a
NPN silicon phototransistor, mounted on opposite sides of a 0.125” (3.18 mm) wide slot in a low-cost black plastic housing.
A variety of aperture sizes are offered (see chart below). The OPB827 and OPB828 are designed fro PCBoard mounting with
a minimum lead length of 0.35” (8.9 mm) while the OPB829Z (wire version) has 24-inch 26 AWG wire leads. Phototransistor
switching occurs when an opaque object passes through the slot.
The OPB827 is offered with 0.305” (7.75 mm) and the OPB828 is offered with 0.220” (5.59 mm) lead spacing for PCBoard
mounting. The OPB829Z has 24” (61 cm) 26 AWG wire leads for remote mounting.
Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more
information.
Applications:
Non-contact object sensing
Assembly line automation
Machine automation
Equipment safety
Machine safety
Part Number
OPB827A
OPB827B
OPB827C
OPB827D
Ordering Information
Slot Width/Depth
Housing
Aperture
Emitter/Sensor
0.120" / 0.315”
IR Transmissive
Opaque
None
None / 0.01"
None / 0.06"
None / 0.01"
Wire Lead Length /
Spacing
0.425" / 0.300"
OPB828A
OPB828B
OPB828C
OPB828D
0.120" / 0.315”
IR Transmissive
Opaque
None
None / 0.01"
None / 0.06"
None / 0.01"
0.425" / 0.220"
OPB829AZ
OPB829BZ
OPB829CZ
OPB829DZ
0.125” / 0.315”
IR Transmissive
Opaque
None
None / 0.01"
None / 0.06"
None / 0.01"
24" / 26 AWG Wire
RoHS
General Note
TT Electronics reserves the right to make changes in product specification without
notice or liability. All information is subject to TT Electronics’ own data and is
considered accurate at time of going to print.
© TT electronics plc
CONTAINS POLYSULFONE
To avoid stress cracking, we suggest using
ND Industries’ Vibra-Tite for thread-locking.
Vibra-Tite evaporates fast without causing structural
failure in OPTEK’s molded plastics.
Applies to: OPB360, OPB370, OPB380, OPB390
and OPB860, OPB870, OPB880, OPB890.
TT Electronics | Optek Technology, Inc.
1645 Wallace Drive, Ste. 130, Carrollton, TX USA 75006 |Ph: +1 972 323 2200
www.ttelectronics.com | sensors@ttelectronics.com
Issue A 11/2016 Page 1
Share Link: 