BD8179MUV 查看數據表（PDF） - ROHM Semiconductor
零件编号
产品描述 (功能)
生产厂家
BD8179MUV Datasheet PDF : 13 Pages
| |||
BD8179MUV
Technical Note
●Notes for use
1) Absolute maximum ratings
Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may
result in IC damage. Assumptions should not be made regarding the state of the IC (short mode or open mode) when such
damage is suffered. A physical safety measure such as a fuse should be implemented when use of the IC in a special
mode where the absolute maximum ratings may be exceeded is anticipated.
2) GND potential
Ensure a minimum GND pin potential in all operating conditions.
3) Setting of heat
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4) Pin short and mistake fitting
Use caution when orienting and positioning the IC for mounting on printed circuit boards. Improper mounting may result in
damage to the IC. Shorts between output pins or between output pins and the power supply and GND pins caused by the
presence of a foreign object may result in damage to the IC.
5) Actions in strong magnetic field
Use caution when using the IC in the presence of a strong magnetic field as doing so may cause the IC to malfunction.
6) Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Ground the IC during assembly steps as an antistatic measure,
and use similar caution when transporting or storing the IC. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process.
7) Ground wiring patterns
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the application's reference point so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the
GND wiring patterns of any external components.
8) This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated.
P/N junctions are formed at the intersection of these P layers with the N layers of other elements to create a variety of
parasitic elements.For example, when the resistors and transistors are connected to the pins as shown in Fig. 18, a
parasitic diode or a transistor operates by inversing the pin voltage and GND voltage.
The formation of parasitic elements as a result of the relationships of the potentials of different pins is an inevitable result
of the IC's architecture. The operation of parasitic elements can cause interference with circuit operation as well as IC
malfunction and damage. For these reasons, it is necessary to use caution so that the IC is not used in a way that will
trigger the operation of parasitic elements, such as the application of voltages lower than the GND (P board) voltage to
input and output pins.
(Pin A)
Resistor
(Pin B)
Transistor (NPN)
B
C
E
(Pin B)
B
C
P+
N
P
P
N
P+
N
Parasitic element
P＋
N
N
P
N
P substrate
GND
P＋
N
(Pin A)
GND
Parasitic elements
GND
Fig.18 Example of a Simple Monolithic IC Architecture
E
GND
Parasitic elements
Parasitic element
GND
9) Overcurrent protection circuits
An overcurrent protection circuit designed according to the output current is incorporated for the prevention of IC
destruction that may result in the event of load shorting. This protection circuit is effective in preventing damage due to
sudden and unexpected accidents. However, the IC should not be used in applications characterized by the continuous
operation or transitioning of the protection circuits. At the time of thermal designing, keep in mind that the current capability
has negative characteristics to temperatures.
10) Thermal shutdown circuit
This IC incorporates a built-in thermal shutdown circuit for the protection from thermal destruction. The IC should be used
within the specified power dissipation range. However, in the event that the IC continues to be operated in excess of its
power dissipation limits, the attendant rise in the chip's temperature Tj will trigger the thermal shutdown circuit to turn off all
output power elements. The circuit automatically resets once the chip's temperature Tj drops.
Operation of the thermal shutdown circuit presumes that the IC's absolute maximum ratings have been exceeded.
Application designs should never make use of the thermal shutdown circuit.
11) Testing on application boards
At the time of inspection of the installation boards, when the capacitor is connected to the pin with low impedance, be sure
to discharge electricity per process because it may load stresses to the IC. Always turn the IC's power supply off before
connecting it to or removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as
an antistatic measure, and use similar caution when transporting or storing the IC.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
11/12
2009.07 - Rev.B
Share Link: 