LPC2210FBD144 查看數據表（PDF） - Philips Electronics
零件编号
产品描述 (功能)
生产厂家
LPC2210FBD144
Philips Electronics
LPC2210FBD144 Datasheet PDF : 49 Pages
| |||
Philips Semiconductors
LPC2210/2220
16/32-bit ARM microcontrollers with external memory interface
Table 4: Pin description …continued
Symbol
Pin (LQFP) Pin (TFBGA) Type
P0.13/DTR1/
MAT1.1
85 [1]
H10 [1]
O
O
P0.14/DCD1/
EINT1
92 [2]
G10 [2]
I
I
P0.15/RI1/
EINT2
99 [2]
E11 [2]
I
I
P0.16/EINT0/ 100 [2]
E10 [2]
I
MAT0.2/CAP0.2
O
I
P0.17/CAP1.2/ 101 [1]
D13 [1]
I
SCK1/MAT1.2
I/O
O
P0.18/CAP1.3/ 121 [1]
D8 [1]
I
MISO1/MAT1.3
I/O
O
P0.19/MAT1.2/ 122 [1]
C8 [1]
O
MOSI1/CAP1.2
I/O
I
P0.20/MAT1.3/ 123 [2]
B8 [2]
O
SSEL1/ EINT3
I
I
P0.21/PWM5/ 4 [1]
CAP1.3
C1 [1]
O
I
P0.22/CAP0.0/ 5 [1]
MAT0.0
D4 [1]
I
O
P0.23
6 [1]
D3 [1]
I/O
P0.24
8 [1]
D1 [1]
I/O
P0.25
21 [1]
H1 [1]
I/O
P0.27/AIN0/
23 [4]
H3 [4]
I
CAP0.1/MAT0.1
I
O
Description
DTR1 — Data Terminal Ready output for UART1.
MAT1.1 — Match output for Timer 1, channel 1.
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip
boot-loader to take over control of the part after reset.
RI1 — Ring Indicator input for UART1.
EINT2 — External interrupt 2 input.
EINT0 — External interrupt 0 input.
MAT0.2 — Match output for Timer 0, channel 2.
CAP0.2 — Capture input for Timer 0, channel 2.
CAP1.2 — Capture input for Timer 1, channel 2.
SCK1 — Serial Clock for SPI1/SSI/Microwire.
SPI/SSI/Microwire clock output from master or input to slave.
MAT1.2 — Match output for Timer 1, channel 2.
CAP1.3 — Capture input for Timer 1, channel 3.
MISO1 — Master In Slave Out for SPI1. Data input to SPI
master or data output from SPI slave.
MAT1.3 — Match output for Timer 1, channel 3.
MAT1.2 — Match output for Timer 1, channel 2.
MOSI1 — Master Out Slave In for SPI1. Data output from SPI
master or data input to SPI slave.
• SPI interface: MOSI line.
• SSI: DX/RX line (SPI1 as a master/slave).
• Microwire: SO/SI line (SPI1 as a master/slave).
CAP1.2 — Capture input for Timer 1, channel 2.
MAT1.3 — Match output for Timer 1, channel 3.
SSEL1 — Slave Select for SPI1/Microwire. Used to select the
SPI or Microwire interface as a slave. Frame synchronization
in case of 4-wire SSI.
EINT3 — External interrupt 3 input.
PWM5 — Pulse Width Modulator output 5.
CAP1.3 — Capture input for Timer 1, channel 3.
CAP0.0 — Capture input for Timer 0, channel 0.
MAT0.0 — Match output for Timer 0, channel 0.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
AIN0 — A/D converter, input 0. This analog input is always
connected to its pin.
CAP0.1 — Capture input for Timer 0, channel 1.
MAT0.1 — Match output for Timer 0, channel 1.
9397 750 14061
Product data sheet
Rev. 02— 30 May 2005
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
8 of 49
Share Link: 