OP162/OP262/OP462–SPECIFICATIONS
ELECTRICAL CHARACTERISTICS (@ VS = +5.0 V, VCM = 0 V, TA = +25؇C, unless otherwise noted)
Parameter
Symbol
Conditions
Min Typ
INPUT CHARACTERISTICS
Offset Voltage
VOS
OP162G, OP262G, OP462G,
45
–40°C ≤ TA ≤ +125°C
H Grade, –40°C ≤ TA ≤ +125°C
D Grade, –40°C ≤ TA ≤ +125°C
0.8
Input Bias Current
Input Offset Current
Input Voltage Range
Common-Mode Rejection
Large Signal Voltage Gain
Long-Term Offset Voltage
Offset Voltage Drift
Bias Current Drift
IB
IOS
VCM
CMRR
AVO
VOS
∆VOS/∆T
∆IB/∆T
–40°C ≤ TA ≤ +125°C
–40°C ≤ TA ≤ +125°C
0
0 V ≤ VCM ≤ +4.0 V,
–40°C ≤ TA ≤ +125°C
70
RL = 2 kΩ, 0.5 ≤ VOUT ≤ 4.5 V
RL = 10 kΩ, 0.5 ≤ VOUT ≤ 4.5 V
65
RL = 10 kΩ, –40°C ≤ TA ≤ +125°C 40
G Grade1
Note 2
360
± 2.5
110
30
88
1
250
OUTPUT CHARACTERISTICS
Output Voltage Swing High
VOH
Output Voltage Swing Low
VOL
Short Circuit Current
ISC
Maximum Output Current
IOUT
IL = 250 µA, –40°C ≤ TA ≤ +125°C 4.95 4.99
IL = 5 mA
4.85 4.94
IL = 250 µA, –40°C ≤ TA ≤ +125°C
14
IL = 5 mA
65
Short to Ground
± 80
± 30
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
PSRR
ISY
VS = +2.7 V to +7 V
–40°C ≤ TA ≤ +125°C
OP162, VOUT = 2.5 V
–40°C ≤ TA ≤ +125°C
OP262, OP462, VOUT = 2.5 V
–40°C ≤ TA ≤ +125°C
120
90
600
500
DYNAMIC PERFORMANCE
Slew Rate
SR
1 V < VOUT < 4 V, RL = 10 kΩ
10
Settling Time
tS
To 0.1%, AV = –1, VO = 2 V Step
540
Gain Bandwidth Product
GBP
15
Phase Margin
φm
61
NOISE PERFORMANCE
Voltage Noise
en p-p
0.1 Hz to 10 Hz
0.5
Voltage Noise Density
en
f = 1 kHz
9.5
Current Noise Density
in
f = 1 kHz
0.4
NOTES
1Long-term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 °C, with an LTPD of 1.3.
2Offset voltage drift is the average of the –40°C to +25°C delta and the +25°C to +125°C delta.
Specifications subj]ect to change without notice.
Max
325
800
1
3
5
600
650
± 25
± 40
+4
600
50
150
750
1
700
850
Units
µV
µV
mV
mV
mV
nA
nA
nA
nA
V
dB
V/mV
V/mV
V/mV
µV
µV/°C
pA/°C
V
V
mV
mV
mA
mA
dB
dB
µA
mA
µA
µA
V/µs
ns
MHz
Degrees
µV p-p
nV/√Hz
pA/√Hz
–2–
REV. C