LTM4620AMPY 查看數據表（PDF） - Linear Technology
零件编号
产品描述 (功能)
生产厂家
LTM4620AMPY Datasheet PDF : 40 Pages
| |||
LTM4620A
APPLICATIONS INFORMATION
The TRACK pin can be controlled by a capacitor placed
on the regulator TRACK pin to ground. A 1.3µA current
source will charge the TRACK pin up to the reference volt-
age and then proceed up to INTVCC. After the 0.6V ramp,
the TRACK pin will no longer be in control, and the internal
voltage reference will control output regulation from the
feedback divider. Foldback current limit is disabled during
this sequence of turn-on during tracking or soft-starting.
The TRACK pins are pulled low when the RUN pin is below
1.2V. The total soft-start time can be calculated as:
tSOFT-START
=
CSS
1.3µA
• 0.6
Regardless of the mode selected by the MODE/PLLIN
pin, the regulator channels will always start in pulse-
skipping mode up to TRACK = 0.5V. Between TRACK =
0.5V and 0.54V, it will operate in forced continuous mode
and revert to the selected mode once TRACK > 0.54V. In
order to track with another channel once in steady state
operation, the LTM4620A is forced into continuous mode
operation as soon as VFB is below 0.54V regardless of the
setting on the MODE/PLLIN pin.
Ratiometric tracking can be achieved by a few simple cal-
culations and the slew rate value applied to the master’s
TRACK pin. As mentioned above, the TRACK pin has a
control range from 0 to 0.6V. The master’s TRACK pin
slew rate is directly equal to the master’s output slew rate
in Volts/Time. The equation:
MR
SR
•
60.4k
=
R
TB
where MR is the master’s output slew rate and SR is the
slave’s output slew rate in Volts/Time. When coincident
tracking is desired, then MR and SR are equal, thus RTB
is equal the 60.4k. RTA is derived from equation:
RTA =
VFB
0.6V
+ VFB − VTRACK
60.4k RFB RTB
where VFB is the feedback voltage reference of the regula-
tor, and VTRACK is 0.6V. Since RTB is equal to the 60.4k
top feedback resistor of the slave regulator in equal slew
rate or coincident tracking, then RTA is equal to RFB with
VFB = VTRACK. Therefore RTB = 60.4k, and RTA = 60.4k in
Figure 6.
In ratiometric tracking, a different slew rate maybe desired
for the slave regulator. RTB can be solved for when SR is
slower than MR. Make sure that the slave supply slew
rate is chosen to be fast enough so that the slave output
voltage will reach it final value before the master output.
For example, MR = 1.5V/1ms, and SR = 1.2V/1ms. Then
RTB = 76.8k. Solve for RTA to equal to 49.9k.
Each of the TRACK pins will have the 1.3µA current source
on when a resistive divider is used to implement tracking
on that specific channel. This will impose an offset on the
TRACK pin input. Smaller values resistors with the same
ratios as the resistor values calculated from the above
equation can be used. For example, where the 60.4k is
used then a 6.04k can be used to reduce the TRACK pin
offset to a negligible value.
Power Good
The PGOOD pins are open drain pins that can be used to
monitor valid output voltage regulation. This pin monitors
a ±10% window around the regulation point. A resistor
can be pulled up to a particular supply voltage no greater
than 6V maximum for monitoring.
Stability Compensation
The module has already been internally compensated for
all output voltages. Table 5 is provided for most applica-
tion requirements. The LTpowerCAD will be provided for
other control loop optimization.
Run Enable
The RUN pins have an enable threshold of 1.4V maximum,
typically 1.25V with 150mV of hysteresis. They control the
turn on each of the channels and INTVCC. These pins can be
pulled up to VIN for 5V operation, or a 5V Zener diode can be
placed on the pins and a 10k to 100k resistor can be placed
up to higher than 5V input for enabling the channels. The
RUN pins can also be used for output voltage sequencing.
In parallel operation the RUN pins can be tie together
For more information www.linear.com/LTM4620A
4620afc
19
Share Link: 