ISL62391CHRTZ 查看數據表（PDF） - Renesas Electronics

零件编号

产品描述 (功能)

生产厂家

ISL62391CHRTZ

High-Efficiency, Triple-Output System Power Supply Controller for Notebook Computers

Renesas Electronics 

ISL62391, ISL62392, ISL62391C, ISL62392C

Where:

- Qg is the total gate charge required to turn on the

high-side MOSFET

- VBOOT, is the maximum allowed voltage decay across

the boot capacitor each time the high-side MOSFET is

switched on

As an example, suppose the high-side MOSFET has a total

gate charge Qg, of 25nC at VGS = 5V, and a VBOOT of

200mV. The calculated bootstrap capacitance is 0.125µF; for a

comfortable margin, select a capacitor that is double the

calculated capacitance. In this example, 0.22µF will suffice.

Use an X7R or X5R ceramic capacitor.

Layout Considerations

As a general rule, power should be on the bottom layer of the

PCB and weak analog or logic signals are on the top layer of

the PCB. The ground-plane layer should be adjacent to the top

layer to provide shielding. The ground plane layer should have

an island located under the IC, the compensation components,

and the FSET components. The island should be connected to

the rest of the ground plane layer at one point.

VIAS TO

GVRIAOSUTNOD

GPRLOANUEND

PLANE

ININDDUUCCTTOORR

HMHMIOIGGOSHHSF-SE-FSITEDISDTEES

GGNNDD

OCOCAUAUPTPTAPAPCUCUITITTTOORRSS

VOUT

SSCCHOOTTTTKKYY

DDIIODDEE

PNNHHOOAADDSSEEEE

LMOLMOOWOSWS-FSF-ESEITDITDSESE

INIPNPUUTT

VVININ

CACAPPAACCITITOORRSS

FIGURE 29. TYPICAL POWER COMPONENT PLACEMENT

Because there are two SMPS outputs and only one PGND pin,

the power train of both channels should be laid out

symmetrically. The line of bilateral symmetry should be drawn

through pins 4 and 18. This layout approach ensures that the

controller does not favor one channel over another during

critical switching decisions. Figure 29 illustrates one example

of how to achieve proper bilateral symmetry.

Signal Ground and Power Ground

The bottom of the ISL62391, ISL62392, ISL62391C and

ISL62392C TQFN package is the signal ground (GND)

terminal for analog and logic signals of the IC. Connect the

GND pad of the ISL62391, ISL62392, ISL62391C and

ISL62392C to the island of ground plane under the top layer

using several vias for a robust thermal and electrical

conduction path. Connect the input capacitors, the output

capacitors, and the source of the lower MOSFETs to the power

ground plane.

PGND (Pin 19)

This is the return path for the pull-down of the LGATE low-side

MOSFET gate driver. Ideally, PGND should be connected to

the source of the low-side MOSFET with a low-resistance, low-

inductance path.

Co

PIN 4 (VCC)

LINE OF SYMMETRY

PIN 18 (PVCC)

ISL6239

L2

L2 U2

Ci

Ci

L1 U1

PGND PLANE

PHASE PLANES

VOUT PLANES

VIN PLANE

L1

Co

FIGURE 30. SYMMETRIC LAYOUT GUIDE

VIN (Pin 17)

The VIN pin should be connected close to the drain of the high-

side MOSFET, using a low resistance and low inductance path.

VCC (Pin 4)

For best performance, place the decoupling capacitor very

close to the VCC and GND pins.

PVCC (Pin 18)

For best performance, place the decoupling capacitor very

close to the PVCC and respective PGND pin, preferably on the

same side of the PCB as the ISL62391, ISL62392, ISL62391C

and ISL62392C ICs.

EN (Pins 11 and 24), and PGOOD (Pin 1)

These are logic signals that are referenced to the GND pin.

Treat as a typical logic signal.

OCSET (Pins 10 and 25) and ISEN (Pins 9 and 26)

For DCR current sensing, the current-sense network,

consisting of ROCSET and CSEN, needs to be connected to the

inductor pads for accurate measurement. Connect ROCSET to

the phase-node side pad of the inductor, and connect CSEN to

the output side pad of the inductor. The ISEN resistor should

also be connected to the output pad of the inductor with a

separate trace. Connect the OCSET pin to the common node

of node of ROCSET and CSEN.

For resistive current sensing, connect ROCSET from the

OCSET pin to the inductor side of the resistor pad. The ISEN

resistor should be connected to the VOUT side of the resistor

pad.

In both current-sense configurations, the resistor and capacitor

sensing elements, with the exclusion of the current sense

power resistor, should be placed near the corresponding IC

pin. The trace connections to the inductor or sensing resistor

should be treated as Kelvin connections.

FN6666 Rev 8.00

August 25, 2015

Page 19 of 22

Share Link: