AD7861 查看數據表（PDF） - Analog Devices

零件编号

产品描述 (功能)

生产厂家

AD7861

11-Bit Resolution Simultaneous Sampling A/D Converter

Analog Devices 

AD7861

DESCRIPTION OF THE REGISTERS

VIN1, VIN2, VIN3 These registers contain the results from

the conversion of the analog input voltages.

AUX

In the AD7861, this register contains the

conversion result of the auxiliary channel

which had been selected by S0, S1.

Reading Results

The A/D conversion results for channels VIN1, VIN2, VIN3

and AUX are stored in the VIN1, VIN2, VIN3 and AUX

registers respectively. The twos complement data is left justified

and the LSB (Data Bit 0) is set to zero. The relationship

between input voltage and output coding is shown in Figure 4.

OUTPUT

CODE

FULL-SCALE

TRANSITION

01 1 1 1 1 1 1 1 1 1 0

000000000000

FS = 5V

LSB = 5V

2048

100000000000

0V

2.5

5V-1LSB

INPUT VOLTAGE

Figure 4. AD7861 Transfer Function

Power Supply Connections and Setup

The nominal power supply level (VDD) is +5 V ± 5%. The

positive power supply (VDD) should be connected to Pins 21

and 36. The SGND and DGND pins should be star point

connected to AGND at a point close to the AD7861.

Power supplies should be bypassed at the power pins using a

0.1 µF capacitor. A 200 nF capacitor should also be connected

between REFIN and SGND.

DIGITAL SIGNAL PROCESSOR INTERFACING

The AD7861 A/D converter is designed to be easily interfaced

to Analog Devices’ family of Digital Signal Processors (DSPs).

Figure 5 shows the interface between the AD7861 and the

ADSP-2101/2105/2115 16-bit fixed point DSP, and the ADSP-

2171 and ADSP-2181 DSP Microcomputers. FLAGOUT from

the DSP is used to initiate the AD7861 conversion and is also

used in conjunction with the BUSY signal to provide an end of

conversion interrupt for the DSP. With M0 and M1 tied low,

the AD7861 is set up in the VIN2, VIN3 channel conversion

mode. By mapping the 12-bit AD7861 data bus into the top 12

bits of the DSP data bus (D12–D23), full-scale outputs from the

AD7861 can be represented as ± 1.0 in fixed point arithmetic.

The AD7861 can operate with a clock frequency in the range of

6.25 MHz to 12.5 MHz. For the ADSP-2101/2105/2115 the

CLKOUT frequency is the system clock frequency. In the case

of the ADSP-2171/2181, the system clock is internally scaled, a

10 MHz system clock will result in a 20 MHz CLKOUT

frequency. If CLKOUT from the ADSP-2171/2181 is above

12.5 MHz, then an external clock divide down circuit will be

necessary.

ADDRESS BUS

A0–A13

DMS

ADSP-2101/

ADSP-2105/

IRQ2

ADSP-2115–12MHz

ADSP-2171–10MHz FLAGOUT

RD

ADSP-2181–10MHz CLKOUT

ADDRESS

DECODE

EN

D0–D23

A0–A1

CS

BUSY

AD7861

CONVST

RD

CLK

M0

M1

D0–D11*

DATA BUS

Figure 5. ADI Digital Signal Processor/Microcomputer

Interface

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

44-Lead Plastic Leadless Chip Carrier

(P-44A)

0.048 (1.21)

0.042 (1.07)

0.048 (1.21)

0.042 (1.07)

0.056 (1.42)

0.042 (1.07)

6

40

7

PIN 1

39

IDENTIFIER

TOP VIEW

(PINS DOWN)

0.180 (4.57)

0.165 (4.19)

0.025 (0.63)

0.015 (0.38)

0.050

(1.27) 0.63 (16.00)

BSC 0.59 (14.99)

0.021 (0.53)

0.013 (0.33)

17

29

18

28

0.020

(0.50)

R

0.656 (16.66)

0.650 (16.51) SQ

0.695 (17.65)

0.685 (17.40) SQ

0.032 (0.81)

0.026 (0.66)

0.040 (1.01)

0.025 (0.64)

0.110 (2.79)

0.085 (2.16)

–6–

REV. B

Share Link: