S25FL016A View Datasheet(PDF) - Spansion Inc.

Part Name

Description

Manufacturer

S25FL016A

16 Megabit CMOS 3.0 Volt Flash Memory with 50-MHz SPI (Serial Peripheral Interface) Bus

Spansion Inc. 

Data Sheet

17.2 SO3 016 wide—16-pin Plastic Small Outline Package (300-mil Body Width)

PACKAGE

JEDEC

SYMBOL

A

A1

A2

b

b1

c

c1

D

E

E1

e

L

L1

L2

N

h

θ

θ1

θ2

SO3 016 (inches)

MS-013(D)AA

MIN MAX

0.093 0.104

0.004 0.012

0.081 0.104

0.012 0.020

0.011 0.019

0.008 0.013

0.008 0.012

0.406 BSC

0.406 BSC

0.295 BSC

.050 BSC

0.016 0.050

.055 REF

.010 BSC

16

0.10 0.30

0˚

8˚

5˚

15˚

0˚

SO3 016 (mm)

MS-013(D)AA

MIN

MAX

2.35

2.65

0.10

0.30

2.05

2.55

0.31

0.51

0.27

0.48

0.20

0.33

0.20

0.30

10.30 BSC

10.30 BSC

7.50 BSC

1.27 BSC

0.40

1.27

1.40 REF

0.25 BSC

16

0.25

0.75

0˚

8˚

5˚

15˚

0˚

NOTES:

1. ALL DIMENSIONS ARE IN BOTH INCHES AND MILLMETERS.

2. DIMENSIONING AND TOLERANCING PER ASME Y14.5M - 1994.

3. DIMENSION D DOES NOT INCLUDE MOLD FLASH,

PROTRUSIONS OR GATE BURRS. MOLD FLASH,

PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.15 mm

. PER END. DIMENSION E1 DOES NOT INCLUDE INTERLEAD

FLASH OR PROTRUSION INTERLEAD FLASH OR PROTRUSION

SHALL NOT EXCEED 0.25 mm PER SIDE. D AND E1

DIMENSIONS ARE DETERMINED AT DATUM H.

4. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE

BOTTOM. DIMENSIONS D AND E1 ARE DETERMINED AT THE

OUTMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF

MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD

FLASH. BUT INCLUDING ANY MISMATCH BETWEEN THE TOP

AND BOTTOM OF THE PLASTIC BODY.

5. DATUMS A AND B TO BE DETERMINED AT DATUM H.

6. "N" IS THE MAXIMUM NUMBER OF TERMINAL POSITIONS FOR

THE SPECIFIED PACKAGE LENGTH.

7. THE DIMENSIONS APPLY TO THE FLAT SECTION OF THE LEAD

BETWEEN 0.10 TO 0.25 mm FROM THE LEAD TIP.

8. DIMENSION "b" DOES NOT INCLUDE DAMBAR PROTRUSION.

ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.10 mm TOTAL

IN EXCESS OF THE "b" DIMENSION AT MAXIMUM MATERIAL

CONDITION. THE DAMBAR CANNOT BE LOCATED ON THE

LOWER RADIUS OF THE LEAD FOOT.

9. THIS CHAMFER FEATURE IS OPTIONAL. IF IT IS NOT PRESENT,

THEN A PIN 1 IDENTIFIER MUST BE LOCATED WITHIN THE INDEX

AREA INDICATED.

10. LEAD COPLANARITY SHALL BE WITHIN 0.10 mm AS MEASURED

FROM THE SEATING PLANE.

3601 \ 16-038.03 \ 8.31.6

January 7, 2008 S25FL016A_00_C3

S25FL016A

33

Share Link: