MACH211SP-10 View Datasheet(PDF) - Unspecified
Part Name
Description
Manufacturer
MACH211SP-10 Datasheet PDF : 33 Pages
| |||
VANTIS
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . –65°C to +150°C
Ambient Temperature
with Power Applied . . . . . . . . . . . . . –55°C to +125°C
Device Junction Temperature . . . . . . . . . . . . . +150°C
Supply Voltage with
Respect to Ground . . . . . . . . . . . . . . –0.5 V to +7.0 V
DC Input Voltage . . . . . . . . . . . .–0.5 V to VCC + 0.5 V
DC Output or
I/O Pin Voltage . . . . . . . . . . . . . –0.5 V to VCC + 0.5 V
Static Discharge Voltage . . . . . . . . . . . . . . . . . 2001 V
Latchup Current (TA = 0°C to 70°C) . . . . . . . . . 200 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent device failure. Functionality at or above
these limits is not implied. Exposure to Absolute Maximum
Ratings for extended periods may affect device reliability.
OPERATING RANGES
Commercial (C) Devices
Ambient Temperature (TA)
Operating in Free Air . . . . . . . . . . . . . . . 0°C to +70°C
Supply Voltage (VCC)
with Respect to Ground . . . . . . . . . +4.75 V to +5.25 V
Operating ranges define those limits between which the
functionality of the device is guaranteed.
DC CHARACTERISTICS over COMMERCIAL operating ranges
Parameter
Symbol
Parameter Description
Test Conditions
Min Typ Max Unit
VOH Output HIGH Voltage
VOL
Output LOW Voltage
VIH
Input HIGH Voltage
IOH = –3.2 mA, VCC = Min, VIN = VIH or VIL 2.4
IOL = 16 mA, VCC = Min, VIN = VIH or VIL
Guaranteed Input Logical HIGH
Voltage for all Inputs (Note 1)
2.0
3.3
V
0.5
V
V
VIL
Input LOW Voltage
Guaranteed Input Logical LOW
Voltage for all Inputs (Note 1)
0.8
V
IIH
IIL
IOZH
IOZL
ISC
ICC
Input HIGH Current
VIN = 5.25 V, VCC = Max (Note 2)
Input LOW Current
VIN = 0 V, VCC = Max (Note 2)
Off-State Output Leakage Current VOUT = 5.25 V, VCC = Max
HIGH
VIN = VIH or VIL (Note 2)
Off-State Output Leakage Current VOUT = 0 V, VCC = Max
LOW
VIN = VIH or VIL (Note 2)
Output Short-Circuit Current
VOUT = 0.5 V, VCC = Max (Note 3)
–30
Supply Current (Static)
VCC = 5 V, TA = 25°C, f = 0 MHz (Note 4)
Supply Current (Active)
VCC = 5 V, TA = 25°C, f = 1 MHz (Note 4)
10
µA
–10
µA
10
µA
–10
µA
–160 mA
40
mA
45
mA
Notes:
1. These are absolute values with respect to device ground and all overshoots due to system and/or tester noise are included.
2. I/O pin leakage is the worst case of IIL and IOZL (or IIH and IOZH).
3. Not more than one output should be shorted at a time. Duration of the short-circuit should not exceed one second.
VOUT = 0.5 V has been chosen to avoid test problems caused by tester ground degradation.
4. This parameter is measured in low-power mode with a 16-bit up/down counter pattern. This pattern is programmed in each PAL
block and is capable of being loaded, enabled and reset.
12
MACH211SP-7/10/12/15 (Com’l)
Share Link: 