MT48LC128M4A2A2TG-75 View Datasheet(PDF) - Micron Technology
Part Name
Description
Manufacturer
MT48LC128M4A2A2TG-75 Datasheet PDF : 55 Pages
| |||
ADVANCE
512Mb: x4, x8, x16
SDRAM
TRUTH TABLE 3 – CURRENT STATE BANK n - COMMAND TO BANK n
(Notes: 1-6; notes appear below and on next page)
CURRENT STATE CS# RAS# CAS# WE#
Any
HXXX
L HHH
L L HH
Idle
L L LH
LLLL
L LHL
LHLH
Row Active
LHL L
L LHL
Read
LHLH
(Auto
LHL L
Precharge
L LHL
Disabled)
L HH L
Write
LHLH
(Auto
LHL L
Precharge
L LHL
Disabled)
L HH L
COMMAND (ACTION)
COMMAND INHIBIT (NOP/Continue previous operation)
NO OPERATION (NOP/Continue previous operation)
ACTIVE (Select and activate row)
AUTO REFRESH
LOAD MODE REGISTER
PRECHARGE
READ (Select column and start READ burst)
WRITE (Select column and start WRITE burst)
PRECHARGE (Deactivate row in bank or banks)
READ (Select column and start new READ burst)
WRITE (Select column and start WRITE burst)
PRECHARGE (Truncate READ burst, start PRECHARGE)
BURST TERMINATE
READ (Select column and start READ burst)
WRITE (Select column and start new WRITE burst)
PRECHARGE (Truncate WRITE burst, start PRECHARGE)
BURST TERMINATE
NOTES
7
7
11
10
10
8
10
10
8
9
10
10
8
9
NOTE: 1. This table applies when CKEn-1 was HIGH and CKEn is HIGH (see Truth Table 2) and after tXSR has been
met (if the previous state was self refresh).
2. This table is bank-specific, except where noted, i.e., the current state is for a specific bank and the commands shown
are those allowed to be issued to that bank when in that state. Exceptions are covered in the notes below.
3. Current state definitions:
Idle: The bank has been precharged, and tRP has been met.
Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no
register accesses are in progress.
Read: A READ burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
Write: A WRITE burst has been initiated, with auto precharge disabled, and has not yet terminated or been
terminated.
4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP
commands, or allowable commands to the other bank should be issued on any clock edge occurring during these
states. Allowable commands to the other bank are determined by its current state and Truth Table 3, and according to
Truth Table 4.
Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the
bank will be in the idle state.
Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the
bank will be in the row active state.
Read w/Auto
Precharge
Enabled: Starts with registration of a READ command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
Write w/Auto
Precharge
Enabled: Starts with registration of a WRITE command with auto precharge enabled and ends when tRP has
been met. Once tRP is met, the bank will be in the idle state.
512Mb: x4, x8, x16 SDRAM
512MSDRAM_D.p65 – Rev. D; Pub 1/02
28
Micron Technology, Inc., reserves the right to change products or specifications without notice.
©2000, Micron Technology, Inc.
Share Link: 