IDT7016L12PFI8 View Datasheet(PDF) - Integrated Device Technology
Part Name
Description
Manufacturer
IDT7016L12PFI8 Datasheet PDF : 21 Pages
| |||
IDT7016S/L
High-Speed 16K x 9 Dual-Port Static RAM
resource, it requests the token by setting the latch. This processor
then verifies its success in setting the latch by reading it. If it was
successful, it proceeds to assume control over the shared resource.
If it was not successful in setting the latch, it determines that the right
side processor has set the latch first, has the token and is using the
shared resource. The left processor can then either repeatedly
request that semaphore’s status or remove its request for that
semaphore to perform another task and occasionally attempt again
to gain control of the token via the set and test sequence. Once the
right side has relinquished the token, the left side should succeed in
gaining control.
The semaphore flags are active LOW. A token is requested by
writing a zero into a semaphore latch and is released when the same
side writes a one to that latch.
The eight semaphore flags reside within the IDT7016 in a
separate memory space from the Dual-Port RAM. This address
space is accessed by placing a LOW input on the SEM pin (which
acts as a chip select for the semaphore flags) and using the other
control pins (Address, OE, and R/W) as they would be used in
accessing a standard static RAM. Each of the flags has a unique
address which can be accessed by either side through address pins
A0 – A2. When accessing the semaphores, none of the other
address pins has any effect.
When writing to a semaphore, only data pin D0 is used. If a low
level is written into an unused semaphore location, that flag will be set
to a zero on that side and a one on the other side (see Truth Table
V). That semaphore can now only be modified by the side showing
the zero. When a one is written into the same location from the same
side, the flag will be set to a one for both sides (unless a semaphore
request from the other side is pending) and then can be written to by
both sides. The fact that the side which is able to write a zero into a
semaphore subsequently locks out writes from the other side is what
makes semaphore flags useful in interprocessor communications.
(A thorough discussion on the use of this feature follows shortly.) A
zero written into the same location from the other side will be stored
in the semaphore request latch for that side until the semaphore is
freed by the first side.
When a semaphore flag is read, its value is spread into all data
bits so that a flag that is a one reads as a one in all data bits and a
flag containing a zero reads as all zeros. The read value is latched
into one side’s output register when that side's semaphore select
(SEM) and output enable (OE) signals go active. This serves to
disallow the semaphore from changing state in the middle of a read
cycle due to a write cycle from the other side. Because of this latch,
a repeated read of a semaphore in a test loop must cause either
signal (SEM or OE) to go inactive or the output will never change.
A sequence WRITE/READ must be used by the semaphore in
order to guarantee that no system level contention will occur. A
processor requests access to shared resources by attempting to
write a zero into a semaphore location. If the semaphore is already
in use, the semaphore request latch will contain a zero, yet the
semaphore flag will appear as one, a fact which the processor will
verify by the subsequent read (see Truth Table V). As an example,
assume a processor writes a zero to the left port at a free semaphore
location. On a subsequent read, the processor will verify that it has
written successfully to that location and will assume control over the
Military, Industrial and Commercial Temperature Ranges
resource in question. Meanwhile, if a processor on the right side
attempts to write a zero to the same semaphore flag it will fail, as will
be verified by the fact that a one will be read from that semaphore on
the right side during subsequent read. Had a sequence of READ/
WRITE been used instead, system contention problems could have
occurred during the gap between the read and write cycles.
It is important to note that a failed semaphore request must be
followed by either repeated reads or by writing a one into the same
location. The reason for this is easily understood by looking at the
simple logic diagram of the semaphore flag in Figure 4.Two
semaphore request latches feed into a semaphore flag. Whichever
latch is first to present a zero to the semaphore flag will force its side
of the semaphore flag LOW and the other side HIGH. This condition
will continue until a one is written to the same semaphore request
latch. Should the other side’s semaphore request latch have been
written to a zero in the meantime, the semaphore flag will flip over to
the other side as soon as a one is written into the first side’s request
latch. The second side’s flag will now stay LOW until its semaphore
request latch is written to a one. From this it is easy to understand that,
if a semaphore is requested and the processor which requested it no
longer needs the resource, the entire system can hang up until a one
is written into that semaphore request latch.
The critical case of semaphore timing is when both sides request
a single token by attempting to write a zero into it at the same time.
The semaphore logic is specially designed to resolve this problem.
If simultaneous requests are made, the logic guarantees that only
one side receives the token. If one side is earlier than the other in
making the request, the first side to make the request will receive the
token. If both requests arrive at the same time, the assignment will
be arbitrarily made to one port or the other.
One caution that should be noted when using semaphores is that
semaphores alone do not guarantee that access to a resource is
secure. As with any powerful programming technique, if sema-
phores are misused or misinterpreted, a software error can easily
happen.
Initialization of the semaphores is not automatic and must be
handled via the initialization program at power-up. Since any
semaphore request flag which contains a zero must be reset to a
one, all semaphores on both sides should have a one written into
them at initialization from both sides to assure that they will be free
when needed.
Using Semaphores-Some Examples
Perhaps the simplest application of semaphores is their applica-
tion as resource markers for the IDT7016’s Dual-Port RAM. Say the
16K x 9 RAM was to be divided into two 8K x 9 blocks which were to
be dedicated at any one time to servicing either the left or right port.
Semaphore 0 could be used to indicate the side which would control
the lower section of memory, and Semaphore 1 could be defined as
the indicator for the upper section of memory.
To take a resource, in this example the lower 8K of Dual-Port
RAM, the processor on the left port could write and then read a zero
in to Semaphore 0. If this task were successfully completed (a zero
was read back rather than a one), the left processor would assume
control of the lower 8K. Meanwhile the right processor was attempt-
6.1482
Share Link: 