ADM9240 View Datasheet(PDF) - ON Semiconductor

Part Name

Description

Manufacturer

ADM9240

Low Cost Microprocessor System Hardware Monitor

ON Semiconductor 

INTERRUPT CLEARING

Reading an Interrupt Status Register will output the contents of

OtthonrecinRegeagcniysIctnleetre,urtprhudepantteceslveieatn,rtsioth.atIshteowcnicleluxrteremredaabidnyoccplreeoarsarsetiidnognunsthiol uthlde

moni-

not be

performed on the register until this has happened, or the result

will be invalid. The time taken for a complete monitoring cycle

is mainly dependent on the time taken to measure the fan speeds,

as described earlier.

The INT output is cleared with the INT_Clear bit, which is Bit

3 of the Configuration Register, without affecting the contents

of the Interrupt (INT) Status Registers. When this bit is high,

the ADM9240 monitoring loop will stop. It will resume when

the bit is low.

TEMPERATURE INTERRUPT MODES

As mentioned earlier, two limit values can be programmed for

ntahnoedrmtaeamHllpyoetsroaTtmuermeedpmeegeraaretsuuesrreelmoHweynesrtt,.eareHsiostLTimemitp(eTraHtOuTrHeYLSiTm),itw(hTiHcOhTi)s,

The interrupt function of the temperature sensor differs from

the interrupt operation of the other inputs in that there are three

interrupt modes, called “One-Time Interrupt” mode, “Default

Interrupt” mode and “Comparator” mode.

DEFAULT INTERRUPT MODE

iEnxdceefeindiitneglyTuHnOtTil

causes an Interrupt that will remain active

reset by reading Interrupt Status Register 1

or

cleared by the INT_Clear bit in the Configuration register.

OOrennscecete, aaannn IIInnnttteeerrrrrruuupppttt eewvvieelnlntot chhcaaussrooaccgccauuirnrrreeoddncbbeyytcchrreoosnssseiinxngtgtTemHOpTe,ratthuerne

conversion has completed. The interrupts will continue to occur

in this manner until the

Operation in the default

tienmteprerurapttumreogdoeesisbiellluoswtraTtHedOTinHYFSTig.ure

10. For clarity, in this illustration the interval between read

operations is shown as considerably longer than the monitoring

cycle time, so that the interrupt is always reasserted after being

reset, before the next read operation occurs.

THOT

and a Hot Temperature Hysteresis Limit (

the temperature measurement, a Hot Temperature Limit (

TEMP

THOTHYST

INT

READ READ READ READ READ READ READ

Figure 10. Temperature INT Output in Default Interrupt

Mode

ONE-TIME INTERRUPT MODE

iEnxdceefeindiitneglyTuHnOtTil

causes an Interrupt that will remain active

reset by reading Interrupt Status Register 1

or

cleared by the INT_Clear bit in the Configuration Register.

Once

reset,

an

an

Interrupt

Interrupt

ewviellnntohtaoscoccucruarrgeadinbuynctriol sthsiengteTmHpOeTra, ttuhreen

ADM9240

gmooedsebiesloilwluTstHraOtTeHdYiSnT.FOigpuerrea1ti1o.nAingatihne,

one-time interrupt

the interval between

read operations is shown as being longer than the monitoring

cycle time.

THOT

TEMP

THOTHYST

INT

READ READ READ READ READ READ READ

Figure 11. INT Output in One-Time Interrupt Mode

COMPARATOR MODE

ritEgeexnmmcoepareieendrdai.LntuIognrwTeoHugthoOneeTtirslcwbtaheuoelsroedtwses,mtThCpHeoeOImrTNa,tpTuIarNreoaTutgotorpweuMisltlbotgeodoloegHwooipLgTehoHr.waOTtT.e.HsINOOliTTknHecYweaSTitlhlies

thermostat with no hysteresis. Operation in the comparator

mode is illustrated in Figure 12.

THOT

TEMP

INT

Figure 12. INT Output in Comparator Mode

RESET INPUT/OUTPUT

RESET (Pin 12) is an I/O pin that can function as an open-

drain output, providing a low going 20 ms output pulse when

Bit 4 of the Configuration Register is set to 1, provided the reset

function has first been enabled by setting Bit 7 of Interrupt

Mask Register #2 to 1. The bit is automatically cleared when

the reset pulse is output. Pin 11 can also function as a RESET

input by pulling this pin low to reset the internal registers of the

ADM9240 to default values. Only those registers that have

power on default values as listed in Table VI are affected by this

function. The DAC register, Value and Limit Registers are not

affected.

NAND TREE TESTS

A NAND tree is provided in the ADM9240 for Automated Test

Equipment (ATE) board level connectivity testing. The device

is placed into NAND Test Mode by powering up with Pin 11

held high. This pin is sampled automatically after power-up and

if it connected high, then the NAND test mode is invoked.

In NAND test mode, all digital inputs may be tested as illus-

trated below. A0/NTEST_OUT will become the NAND tree

output pin. To perform a NAND tree test, all pins included in

the NAND tree should be driven high.

REV. 0

Rev. 2 | Page 15 of 22 | www.onsemi.com

–15–

Share Link: